Preparation and Applications of Cobalt–Rhenium Alloy Coatings


In recent years, researchers have shown growing interest in electrodeposited rhenium alloys, driven by the demand for high-strength materials in mechanical engineering and the aerospace industry.

In recent years, researchers have shown growing interest in electrodeposited rhenium alloys, driven by the demand for high-strength materials in mechanical engineering and the aerospace industry. At the same time, they are actively seeking substitutes for platinum-group metals that can serve as effective electrocatalytic materials in a wide range of processes.

1. Electroplated Coatings

The quality, structure and chemical composition of electroplated coatings depend largely on the precise formulation and complex composition of the electrolyte, as well as on the deposition regime employed. Rhenium is generally released from aqueous solutions in the form of polyoxides and readily forms electrolytic alloys with iron-group metals such as cobalt. Electrolytic rhenium and its alloys with iron-group metals can also be obtained from aqueous salt-based electrolytes.

        Under certain conditions, crack-free, high-quality coatings can be obtained only in a potentiostatic regime and only when the coating thickness is limited to 200–300 nm. Coatings in the micrometre range, by contrast, are prone to degradation during storage. Aqueous electrolytes show considerable promise for coatings with thicknesses of 1–10 mm. By using aqueous electrolytes of complex composition, alloys with different rhenium contents can be produced.

2. Cobalt–Rhenium Alloy Coatings

As reported in References 2 and 3, high-quality coatings containing 45–65 at% rhenium can be obtained by electrodeposition from a citric acid (Cit) electrolyte at pH 3.5. The composition and properties of the electroplated coating are governed by the composition of the electrochemically active complexes — that is, of the ions that react directly at the electrode surface and are discharged at the cathode to form the metal or alloy.

       Studies on the electrodeposition of binary Co–Re (cobalt–rhenium) alloys have shown that, in an electrolyte at pH 3.5, rhenium can be reduced to the metal by adsorbed hydrogen atoms, a process promoted by the parallel cathodic reaction of hydrogen evolution. In acidic media, many proton donors are present, such as protonated cobalt–citrate complexes and an excess of protonated citrate ions. On this basis, the researchers proposed a new concept for depositing binary alloys from solution, in which water serves as the principal proton donor and metal formation relies on non-protonated complexes. They therefore carried out experiments in which coatings were deposited from a citrate electrolyte at pH 9.0. In such a solution — particularly in view of the alkalinisation of the region near the cathode — only non-protonated cobalt complexes and their bimetallic complexes are electroactive.

       In the electrodeposition of binary Co–Re (cobalt–rhenium) alloys from a citrate electrolyte, raising the pH from 3.5 increases the rhenium content of the alloy. As shown in Figure 1, the average rhenium content at every applied current density rises by approximately 20 at% as the pH increases. This behaviour indicates that electrolytes containing complexing agents can raise the overpotential for metal deposition, giving finer-grained deposits, and can bring the deposition potentials of the two metals closer together, thereby favouring the formation of an electrolytic alloy.

Figure 1. Rhenium content as a function of current density for deposition from citrate (Cit) electrolytes at pH 3.5 (1) and 9.0 (2), and from a citrate–pyrophosphate (Cit–PPi) electrolyte (3).

At pH 9.0, rhenium is present mainly as perrhenate ions, a form that does not readily give rise to strong chemical complexes that are difficult to electrodeposit. Although the electroreduction of perrhenate can produce rhenium oxide films, as the researchers have shown, neither cobalt nor rhenium can be deposited on its own as a solid metallic coating from alkaline solutions containing an excess of ligand. Nevertheless, a synergistic effect makes the formation of an electrolytic alloy possible. This effect cannot be explained solely by the formation of bimetallic complexes in solution; it is more likely attributable to the immediate formation of electroactive species following adsorption of metal-containing complexes on the cathode surface.

Figure 2. Current efficiency of Co–Re alloys deposited from different electrolytes (a), and partial current efficiencies of the two metals (b).

Electrodeposition from citrate electrolytes can produce X-ray amorphous coatings containing up to 78 at% rhenium, which exhibit excellent performance owing to their distinctive structure and high rhenium content. In citrate–pyrophosphate electrolytes, the researchers further observed a lower overpotential for cobalt electroreduction, which sharply reduced the rhenium fraction in the coating to 12 at% while yielding a clearly crystalline structure. These findings not only broaden our understanding of how to control the structure of alloy coatings, but also open up new possibilities for tuning the alloy composition so as to obtain non-magnetic or ferromagnetic coatings.

Figure 3. Surface morphology of Co–Re alloys deposited from Cit (a)–(c) and Cit–PPi (d)–(f) electrolytes at different deposition current densities: 5 mA/cm² — (a), (d); 10 mA/cm² — (b), (e); 30 mA/cm² — (c), (f).

In summary, the chemical composition and microstructure of alloy coatings can be controlled by adjusting the electrolyte composition and the electrodeposition conditions, and these changes have a profound influence on the magnetic and electrocatalytic properties of the coatings. These results provide a new perspective on the design and application of alloy coatings, especially in high-technology fields that require specific magnetic properties and electrochemical stability. As research into these materials continues, further technological breakthroughs in materials science and engineering can be expected in the future.

Rheniumet specializes in the production, processing, and distribution of rare and precious metal materials and products, with strong in-house development capabilities and industrial-scale manufacturing. Our main products include ruthenium dioxide, ruthenium trichloride, ruthenium powder, ultrafine ruthenium powder, high-purity ruthenium rods, ruthenium sputtering targets, and a wide range of metal and alloy sputtering targets. We provide high-purity, high-quality, high-performance ruthenium-based catalytic and conductive materials tailored to the electronic paste industry—with ultrafine ruthenium powder, ruthenium dioxide, and ruthenium trichloride as core feedstocks—supporting the R&D and production of companies in thick-film resistors, ruthenate resistors, and MLCC inner-electrode pastes. Please feel free to contact us for more information!

Contact person: Rosanna Zhang

Tel: +86 18608418245

Email: sales@super-carbide.com

References

  1. Y. Yapontseva, V. Kublanovsky, T. Maltseva, Y Troshchenkovb and O. Vyshnevskyic. Mater. Adv., 2023, 4, 3662-3670.

2. Yu. S. Yapontseva, T. V. Maltseva, V. S. Kublanovsky, O. A. Vyshnevskyi and Yu. N. Troshchenkov, Int. J. Refract. Met. Hard Mater., 2021, 96, 105469.

  1. Y. Yapontseva, V. Kublanovsky and O. Vyshnevskyi, J. Alloys Compd., 2018, 766, 894–901.

Related Downloads